BrotherHobby SE 2810 1180KV Motor (CW) – 6S, 12N14P, M5 Thread, 19x19mm Mount, N52H

Description

Overview

The BrotherHobby SE 2810 1180KV Motor (CW) is a 6S-capable motor designed for builds using larger propellers, with an M5 prop adapter shaft thread and a 19 x 19 mm M3 mounting pattern.

Key Features

• SUS420 heat-treated steel shaft (SUS420)
• 7075 aluminum caps / bell cap (Al 7075), hard-anodized
• N52H arc magnet rotor (N52H)
• High-precision bearings (Japanese NMB 12 x 6 x 4)
• TU1 grade enameled wire; wire spec: 18# with 25 cm length
• Ultra-thin silicon steel stator sheet: 0.2 mm Kawasaki silicon steel
• Configuration: 12N14P

For pre-sales and technical support, contact [email protected] or visit https://rcdrone.top/.

Specifications

Model	SE 2810
KV	1180KV
Configuration	12N14P
Base casing material	Al 7075
Bell cap material	Al 7075
Stator material	0.2mm Kawasaki silicon steel
Stator height (mm)	10 (Kawasaki 1200# 0.2MM)
Stator dimension (mm)	28.00
Motor dimension (mm)	33.3 x 39
Prop adapter shaft thread	M5
Shaft	SUS420
Bolt pattern	M3 (19 x 19mm)
Bearings	Japanese NMB 12 x 6 x 4
Rotor	N52H arc magnets
No. of Cells (LiPo)	6S
Wire AWG	18# 25cm length (also shown as 18#, 250mm)
Weight	67.2g
Weight including cable (g)	68.10
Internal Resistance (m)	63.60
Idle Current @ 10V (A)	1.03A/10V
Max power (W)	940.80
Max Current (A)	39.20
Insulation Resistance	>= 0.5M
Dynamic balance requirement standards	<= 3mg
Coil Test	PASS

Prop Test Report (1180KV)

Test setup (as shown)

• Propeller: HQ 7X4X3
• ESC: 6S 45A

Load Test Data (HQ 7X4X3)

Throttle (%)	Voltage (V)	Current (A)	RPM	Thrust (gf)	Input Power (W)	Thrust efficiency (G/W)
30	24.00	2.00	7812	326.00	48.00	6.79
40	24.00	3.10	9440	472.00	74.40	6.34
50	24.00	5.00	11067	660.00	120.00	5.50
60	24.00	9.00	13387	1004.00	216.00	4.65
70	24.00	15.00	15420	1386.00	360.00	3.85
80	24.00	23.80	17756	1862.00	571.20	3.26
90	24.00	32.00	19410	2257.00	768.00	2.94
100	24.00	39.20	19880	2436.00	940.80	2.59

• Inside motor copper wire temperature: 76C (ambient temperature: 26C)
• Temperature note: inside copper wire temperature measured running 2 minutes at 100% throttle; bench data for reference only.

Whats Included

• SE 2810 motor x1
• M3*8 screw x4
• M5 flange nut x1

Applications

• 6S multirotor builds using 7-inch class propellers

Notes

• Some images also show specifications and prop test data for a different SE 2810 variant (1350KV). Those values are not for the 1180KV (CW) version listed on this page.

Details

The BrotherHobby SE 2810 motor is clearly labeled 2810-1180KV on the housing for easy identification during builds and replacements.

BrotherHobby SE 2810 motor specs list a 1350KV rating, 67.2g weight, and up to 2.5kg maximum pull force per motor.

The BrotherHobby SE 2810 1180KV motor features a compact black can and threaded shaft for straightforward prop installation on larger drone setups.

The BrotherHobby SE 2810 1180KV motor uses an M5 shaft and a 4M3 mounting pattern, with a 39mm body length and 33.3mm diameter shown in the drawing.

The BrotherHobby SE 2810 1180KV motor comes with four M38 screws and an M5 flange nut for mounting.

The BrotherHobby SE 2810-1350KV motor report lists key specs like 12N14P configuration, 6S support, and HQ 7×3.5×3 prop test results.

The SE 2810 1180KV motor report includes a dimension drawing and a 24V HQ 7x4x3 prop test table with thrust, current, and efficiency readings.