Sale!
Happymodel Mobula7 1S ELRS 75mm BNF Brushless Whoop (2.4Ghz)

Happymodel Mobula7 1S ELRS 75mm BNF Brushless Whoop (2.4Ghz)

Original price was: $79.00.Current price is: $39.50.

SKU: UIFU260216166 Category:

Description

This drone features the all new 5in1 AIO board that includes 2.4Ghz ExpressLRS V2.0, OpenVTX (up to 400mW) along with 4x 12A BLheli_S ESC, and BetaFlight OSD all built into a F4 whoop flight controller board.

The new RS0802 motors come with a new unibell design, and use a 1.5mm shaft with a PCB bottom plate, high efficiency and much more reliable.

&feature=emb_title

Key Features

  • X12 5-IN-1 AIO flight controller built-in 2.4G ELRS V3.0 and Openvtx
  • VTX Power up to 400mw
  • ELRS V3.0 Support
  • NEW RS0802 KV20000 motors
  • Runcam Nano3 The lightest 1/3 CMOS 800TVL Camera
  • Smooth and powerful
  • Compatible for 1S Lipo/LIHV
  • Recommend 1S 450mah/550mah/650mah battery(Not include)

&feature=emb_title

Specification

  • Brand Name: Happymodel
  • Item Name: Mobula7 1S 75mm Micro FPV whoop drone
  • Wheelbase: 75mm
  • Size: 99mm*99mm*40mm
  • Weight: 24g
Motor Mode: RS0802 KV20000
Configu-ration:9N12P
Stator Diamter:8mm
Stator Length:2mm
Shaft Diameter:1.5mm
Motor Dimension(Dia.*Len):10.5mm*13.5mm
Weight(g):2.0g
No.of Cells(Lipo):1S only
Propellers Weight:0.24g
Material:PC
Pitch:1 inch
Props Dia:40mm
Center Thickness:5mm
Center Hole Dia:1.5mm
Flight controller X12 ELRS V1.0 flight controller built-in ELRS 2.4G receiver Target: CRAZYBEEF4SX1280
X12 Frsky V1.0 flight controller built-in SPI Frsky 2.4G receiver Target: CRAZYBEEF4FR
X12 Flysky V1.0 flight controller built-in SPI Flysky 2.4G receiver Target: CRAZYBEEF4FS
X12 PNP V1.0 flight controller without onboard receiver Target: CRAZYBEEF4DX
MCU:STM32F411CEU6 (100MHZ, 512K FLASH)
Sensor: MPU6000 or ICM20689(SPI connection)
Mount hole size: 25.5mm*25.5mm
Power supply: 1S battery input (DC 2.9V-4.35V)
Built-in 12A(each) Blheli_S 4in1 ESC
Built-in Betaflight OSD(SPI Control)
Built-in 5.8G OpenVTX 0mw~400mw
Built-in ExpressLRS 2.4G,Frsky D8/D16,Flysky AFHDS 2A
Built-in voltage detection
Built-in current sensor
Onboard 4in1 ESC Power supply: 1S LiPo/LiPo HV
Current: 12A continuous peak 15A (3 seconds)
Support BLHeliSuite programmable
Factory firmware: Z_H_30_REV16_7.HEX
Default protocol: DSHOT300
Support Bluejay firmware
Onboard SPI ExpressLRS 2.4GHz Receiver

( 2.4G ELRS Receiver Version)

 Packet Rate option: 50Hz/150Hz/250Hz/500Hz
ExpressLRS Firmware version: V3.0
RF Frequency: 2.4GHz
Antenna: SMD antenna
Telemetry output Power: <12dBm
Receiver protocol: SPI ExpressLRS
Compatible with ExpressLRS V2.0 TX Module
Couldn’t flash separately ExpressLRS firmware
Onboard Frsky SPI D8/D16 receiver compatible

( Compatible Frsky Receiver Version)

 SPI BUS receiver Frsky D8 compatible
Compatible Non-EU transmitter D8 model
Channels: 8ch
No ground interference ( Transmitter and receiver 1 m from the ground): 200meter
Failsafe support
Onboard Flysky SPI receiver compatible

( Compatible Flysky Receiver Version)

 SPI BUS receiver
Protocol: AFHDS and AFHDS-2A Switchable
Channels: 8ch(AFHDS) or 14ch(AFHDS-2A)
No ground interference ( Transmitter and receiver 1 m from the ground): 200meter
Failsafe support
PNP Version (without onboard receiver) Full UART1 for external Receiver
Support CRSF/GHOST/SBUS/IBUS/DSMX protocol
IR1 pad(invert RX1) used for SBUS input
Onboard 5.8g OPENVTX Firmware version: OPENVTX
Smart audio v2.1
PIT Mode support
RCE Mode support
Channels:48ch
Transmitting Power: 0/RCE/25mw/100mw/400mw
Power supply: DC 5V
Current (5v): <650ma (400mw)
Runcam Nano3 Model: RunCam Nano 3
Image Sensor: 1/3″ CMOS
Horizontal Resolution: 800TVL
Lens : 2.1mm(M8) FOV 150
Signal System: NTSC
S/N Ratio: >50dB
Electronic Shutter Speed: Auto
Auto Gain Control (AGC): Auto
Min. Illumination: [email protected]
D-WDR: Auto
Day/Night: Color
Power:DC 3-5.5V
Current: 110mA@5V [email protected]
Housing Material: ABS
Net Weight: 1.2g
Dimensions: L14mm*W14mm*H9mm
Recommend 1S Lipo Battery (Not included)

Capacity: 650mAh
Voltage: 3.8v
Continuous Discharge Rate: 30C
Instantaneous discharge rate: 60C
Size: 60mmx18mmx8mm
Weight: 16g
Connector: PH2.0

Included

  • 1x Mobula7 1S FPV Racing Drone
  • 1x Propeller disassemble Tool
  • 1x Extra Canopy
  • 1x Parallel charging board

Reviews

There are no reviews yet.

Be the first to review “Happymodel Mobula7 1S ELRS 75mm BNF Brushless Whoop (2.4Ghz)”

Related products